Our master bath doesn’t have an exhaust fan and I’d like to add one to help with the humidity. It’s the primary bathroom of use upstairs and the 2nd full bath is on the other side of the wall.

Can I use a splitter to tie the other bathroom’s exterior vent to the new exhaust? If I did I’d put the splitter closest to the vent to help prevent blow back to the other bathroom. They’re both smaller bathrooms (50sqft and 100sqft).

Or is it just better to put it on it’s own exhaust vent?

    • nrezcm@lemmy.worldOP
      link
      fedilink
      English
      arrow-up
      2
      ·
      1 year ago

      Sweet thanks! That’s pretty much what I was thinking. Only time the 2nd bath gets used is if we have guests over or I’m washing the dog. Should be a good stop hold until we sell or rent it out at least.

  • kiwifoxtrot@lemmy.world
    link
    fedilink
    English
    arrow-up
    5
    ·
    1 year ago

    Shouldn’t be a problem to tie them both together. You’ll want to add check valves on both lines before they join together. If you haven’t bought a fan yet, I highly recommend the Panasonic WhisperFit series. They pull a ton of air, are energy efficient, and are very quiet. I went from having condensation on my mirror after a shower to nothing at all.

    • nrezcm@lemmy.worldOP
      link
      fedilink
      English
      arrow-up
      3
      ·
      1 year ago

      Ah good suggestion with the check valve. I just replaced our downstairs fan and it was a cheap one I got from HD but it worked well. You didn’t happen to go with one of the humidity sensing WhisperFits did you? Looks like they have several with adjustable CFM so that actually might be a good fit for us when we go to renovate it in the future.

      • kiwifoxtrot@lemmy.world
        link
        fedilink
        English
        arrow-up
        2
        ·
        1 year ago

        I have one that I can adjust the CFM and the time it takes to shut off. I have it configured to run for 5 minutes after I turn off the switch on the wall. This does require you to run power directly to the unit and a signal wire to your switch. I believe they also make electrical switches with timers that are easier to retrofit.

        • nrezcm@lemmy.worldOP
          link
          fedilink
          English
          arrow-up
          1
          ·
          1 year ago

          That should be too easy. I’d have to run romex either way since there is just a light in there right now.

      • fodder69@lemmy.world
        link
        fedilink
        English
        arrow-up
        2
        ·
        1 year ago

        100% on check valves; technically each fan has to have it’s own vent per code. Decent fans have a check in them but better safe than sorry. I’d put a separate exhaust unless it’s really hard to get to.

        +1 on humidity sensors but they can make wiring more complicated especially if you have a light as well.

        I love Panasonic’s. Not cheap but humidity sensor, variable cfm and quiet.

        Noisy fans make you feel better but all that higher pitched exhaust fan noise stays in the room to make you feel better but trust me the bass noise comes through outside!

        • nrezcm@lemmy.worldOP
          link
          fedilink
          English
          arrow-up
          1
          ·
          1 year ago

          Thanks for the feedback. Honestly both routes are probably the same amount of work so maybe I just get done with it and do a new vent so I don’t need to worry about it when it comes time to sell.

  • CSFFlame@lemmy.world
    link
    fedilink
    English
    arrow-up
    2
    ·
    1 year ago

    I would do individual vents, but there are vent dampers that would prevent blowback… though I’m not sure if they would rust with constant humid air going through them…