• czardestructo@lemmy.world
    link
    fedilink
    English
    arrow-up
    136
    arrow-down
    1
    ·
    1 year ago

    There is nothing wrong with LED lights. There is just a big problem with cheap, poorly designed LEDs. You can use proper optics and control the light exceptionally well and put it exactly where its needed with very little spill over or reflections up. You can also chose whatever color and color rendering index (CRI) you like but all of this costs more money and municipal bean counters are drunk on the lowest bidder. So we get glare bomb blue light shows. I used to design this stuff so feel free to ask questions.

    • benwubbleyou@lemmy.world
      link
      fedilink
      English
      arrow-up
      11
      ·
      1 year ago

      So I’m a wedding photographer and in the past 3 years I have noticed an increased amount of the lights at venues strobe or have really bad banding when I set my shutter speed to higher than 120. My assumption is that the new LED lights are flickering at a consistent rate to save energy but at the cost of the photos I take. Is this the case? That cheaper LED lights will flicker like that?

      • CmdrShepard@lemmy.one
        link
        fedilink
        English
        arrow-up
        8
        ·
        edit-2
        1 year ago

        The strobing is due to the way they’re powered. When converting AC power to DC power, you can either convert the positive half of the AC sine wave (half rectified) or both positive and negative sides of the AC wave (full rectified). Cheap lights use half rectifiers so as the AC feeds in, the light is only getting powered half the time and off the other half of the time. This happens so rapidly that we don’t really see it with our eyes, but with a camera it’s very noticeable. AC cycles at 60 cycles per second (in the US), so it makes sense that you’re seeing it at 120 shutter speed as this equates to 60fps.

        I’d consider talking to some of these venues about it as I assume they’re typically used for events that’ll be filmed, so using shitty lighting is ruining it for everyone same as if they had the toilets sitting in the middle of the dance floor.

        • Sir_Kevin@discuss.online
          link
          fedilink
          English
          arrow-up
          2
          ·
          1 year ago

          Add to that, the way they are damned is typically by flickering them off and on aka Pulse width modulation. This is super common in LED strips.

      • Solemn@lemmy.dbzer0.com
        link
        fedilink
        English
        arrow-up
        3
        ·
        1 year ago

        So LEDs are generally very bright by default, and there’s a limit to how much you can really dim that. The solution used is often to flicker the LED at high speed, imperceptible to human eyes, called Pulse Width Modulation (PWM). Basically, by changing the percentage of time the LED is on (the width of the ON pulse) you change the perceived brightness off the light.

        Cheap LED designs do this slower, cause the hardware and LEDs are cheaper. It’s not really to save energy, but to adjust brightness and manage heat.

        Also, probably more importantly, cheap LED bulb designs just don’t deal with AC current as well, so you get the 60Hz flicker from the electrical line cause that doesn’t get regulated out correctly when converting to DC.

      • Troy@lemmy.ca
        link
        fedilink
        English
        arrow-up
        2
        ·
        1 year ago

        You’re seeing the 60Hz sinusoid caused by using AC electricity. 60 peaks, 60 troughs – but the like is actually turning on and off 120 times per second when on AC, unless it’s first converted to DC. Cheap LEDs just feed AC.

      • Kiosade@lemmy.ca
        link
        fedilink
        English
        arrow-up
        2
        ·
        1 year ago

        So what I heard a long time ago is that all LED lights essentially strobe on and off constantly, faster than the human eye can detect, though i’m willing to bet the better ones are constructed in a way that you wouldn’t notice at all (whether with the naked eye, or through a high shutter speed camera, as you mentioned), but the shittier ones strobe more frequently and not at a rate that’s as smooth/consistent as the better ones. As a little anecdote, I bought a lower quality light-tablet for tracing a while back, and was getting crazy headaches after using it for maybe an hour or so. Had to stop using it, and I think it must be an example of what poor quality LEDs are like.

        • czardestructo@lemmy.world
          link
          fedilink
          English
          arrow-up
          3
          ·
          1 year ago

          So LEDs can either be strobed or powered consistently with no blinking at all. It’s a design choice and it depends on how you convert the power from AC to DC and how you want to control the brightness of the LED. It’s cheaper to feed an LED power that is modulated/strobes so all the cheap vendors do that. You can also get away with strobing the LED to achieve a brightness assuming you do it at a very high frequency so our eyes don’t perceive it. If you buy a quality LED light fixture there should be no strobing effect what so ever.

      • xpinchx@lemmy.world
        link
        fedilink
        English
        arrow-up
        2
        ·
        1 year ago

        Not sure why, but the high power LEDs you see in cars do this if they’re cheap or done poorly. Mine came with like an ant-flicker ballast or something.